Keurig espresso makers are a well-liked technique to make a fast and simple cup of espresso. Nevertheless, in case your Keurig begins to malfunction, chances are you’ll have to take it aside to troubleshoot the issue. Taking aside a Keurig can seem to be a frightening activity, however it’s truly fairly easy with the proper instruments and directions.
Earlier than you begin taking aside your Keurig, make sure you unplug it from the facility outlet. Additionally, you will want to collect just a few instruments, together with a Phillips head screwdriver, a flathead screwdriver, and a pair of pliers. After you have your instruments, you may observe the steps beneath to take aside your Keurig:
First, take away the water reservoir. The water reservoir is situated on the again of the Keurig. To take away it, merely elevate it up and pull it out. Subsequent, take away the drip tray. The drip tray is situated beneath the brew head. To take away it, merely pull it out. Lastly, take away the brew head. The brew head is situated on the prime of the Keurig. To take away it, flip the locking lever to the unlock place and pull the brew head up and out.
Disassembling the Outer Casing
Earlier than you may entry the internal workings of your Keurig, you want to disassemble the outer casing. This can be a comparatively easy course of, nevertheless it’s vital to observe the steps rigorously to keep away from damaging your espresso maker.
1. Take away the highest cowl
Begin by eradicating the highest cowl of the Keurig. On most fashions, the highest cowl is held in place by two screws situated behind the machine. Use a Phillips head screwdriver to take away the screws, then elevate the highest cowl off the machine.
As soon as the highest cowl is eliminated, you will notice the water reservoir and the brewing chamber. The water reservoir is situated on the left facet of the machine, and the brewing chamber is situated on the proper facet.
To take away the water reservoir, merely elevate it up and out of the machine. To take away the brewing chamber, press down on the discharge button situated on the highest of the chamber, then elevate the chamber out of the machine.
2. Take away the facet panels
The following step is to take away the facet panels of the Keurig. On most fashions, the facet panels are held in place by two screws situated on the prime and backside of every panel. Use a Phillips head screwdriver to take away the screws, then elevate the facet panels off the machine.
As soon as the facet panels are eliminated, you will notice the inner parts of the Keurig. These parts embrace the heating ingredient, the pump, and the management board.
3. Take away the underside cowl
The ultimate step is to take away the underside cowl of the Keurig. On most fashions, the underside cowl is held in place by 4 screws situated on the corners of the duvet. Use a Phillips head screwdriver to take away the screws, then elevate the underside cowl off the machine.
As soon as the underside cowl is eliminated, you should have entry to the entire inside parts of the Keurig. Now you can start troubleshooting or repairing your espresso maker.
Eradicating the Water Reservoir
Eradicating the water reservoir is easy and might be completed in only a few steps. Guarantee that the espresso maker is turned off and unplugged earlier than beginning.
1. Find the water reservoir launch button.
The water reservoir launch button is normally situated on the again or facet of the espresso maker. It’s sometimes a small, black button.
2. Press the water reservoir launch button and pull the reservoir straight up.
After you have situated the water reservoir launch button, press it and pull the reservoir straight up. The reservoir ought to come out simply. If you’re having hassle eradicating the reservoir, attempt wiggling it gently backward and forward.
The reservoir has quite a lot of inside parts which will dislodge throughout the elimination or filling course of. Here is a visible information to assist establish these parts:
| Part | Description |
|---|---|
| Water Degree Indicator | A float that rises and falls with the water degree. |
| Water Degree Sensor | A sensor that detects the water degree and shuts off the espresso maker when the reservoir is empty. |
| Pump | A pump that circulates the water via the espresso maker. |
3. As soon as the reservoir has been eliminated, you may clear it with heat, soapy water.
Be certain to rinse the reservoir completely and permit it to dry fully earlier than changing it.
Disconnecting the Electrical Wires
As soon as you’ve got eliminated the outer casing, it is time to disconnect {the electrical} wires. These wires are what energy the Keurig, so it is vital to watch out when dealing with them.
Step 1: Find the Electrical Wires
{The electrical} wires are situated on the underside of the Keurig. They’re normally held in place by a plastic clip.
Step 2: Take away the Plastic Clip
Use a screwdriver or your fingernails to take away the plastic clip. This may launch {the electrical} wires.
Step 3: Disconnect the Electrical Wires
As soon as {the electrical} wires are launched, you may disconnect them. To do that, merely pull the wires aside.
| Wire Shade | Connection |
|---|---|
| Black | Frequent |
| Crimson | Line |
| White | Impartial |
Eradicating the Plunger and Needles
To take away the plunger and needles, first take away the highest cowl of the Keurig. Then, find the plunger meeting. It’s a cylindrical-shaped half that’s situated within the heart of the machine. Grip the plunger meeting and pull it straight up. This may take away the plunger and needles from the machine.
As soon as the plunger and needles have been eliminated, you may clear them. To wash the plunger, merely wipe it down with a humid fabric. To wash the needles, use a delicate brush to take away any espresso grounds or particles. As soon as the plunger and needles are clear, you may reassemble the Keurig.
Cleansing the Plunger Meeting
| Step | Description |
|---|---|
| 1 | Take away the highest cowl of the Keurig. |
| 2 | Find the plunger meeting. It’s a cylindrical-shaped half that’s situated within the heart of the machine. |
| 3 | Grip the plunger meeting and pull it straight up. This may take away the plunger and needles from the machine. |
| 4 | Wipe down the plunger with a humid fabric. |
| 5 | Use a delicate brush to take away any espresso grounds or particles from the needles. |
| 6 | Reassemble the Keurig. |
Accessing the Inner Parts
To entry the inner parts of the Keurig machine, you need to rigorously disassemble the outside housing. Here is a step-by-step information to take action:
1. Unplug the Machine
Start by unplugging the Keurig machine from the facility outlet to make sure your security.
2. Find the Screws
Subsequent, find the screws that maintain the outside housing collectively. On most Keurig fashions, these screws are discovered on the again of the machine or beneath the drip tray.
3. Take away the Exterior Housing
Use a screwdriver to take away the screws, after which gently elevate the outside housing off the machine. Watch out to not injury any wires or inside parts.
4. Find the Screws Holding the Chassis
Inside the outside housing, you’ll find the chassis, which holds the inner parts in place. Find the screws that maintain the chassis in place, that are sometimes discovered on the edges or backside.
5. Take away the Chassis
Use a screwdriver to take away the screws, after which rigorously elevate the chassis out of the machine. Take care to not pull any wires or injury any parts.
6. Troubleshooting
Typically throughout disassembly, chances are you’ll encounter some frequent points. Here is a troubleshooting information that will help you resolve them:
| Situation | Answer |
|---|---|
| Stripped screw | Use a rubber band or small piece of paper between the screwdriver and the screw to realize further grip. |
| Caught parts | Gently faucet on the part with a rubber mallet or use a skinny, flat software to pry it aside. |
| Broken or disconnected wires | Examine the wires for any injury or disconnection. If essential, reconnect or restore the wires utilizing wire connectors or electrical tape. |
Disconnecting the Management Board
As soon as you’ve got eliminated the highest cowl and entrance panel, it is time to disconnect the management board. This can be a delicate step, so take your time and watch out to not injury any of the parts.
Step 1: Establish the Management Board
The management board is normally situated within the heart of the machine, behind the entrance panel. It is a inexperienced circuit board with a variety of wires and connectors connected to it.
Step 2: Disconnect the Wires
Use a pair of needle-nose pliers to disconnect the wires from the management board. There are two sorts of wires: energy wires and knowledge wires. Energy wires are normally thicker and have a black or pink insulation. Information wires are thinner and have a yellow or white insulation.
Step 3: Take away the Connectors
As soon as the wires are disconnected, you may take away the connectors from the management board. Connectors are small plastic plugs that join the wires to the board. To take away a connector, gently pry it up with a small screwdriver.
Step 4: Carry the Management Board
As soon as the connectors are eliminated, you may elevate the management board up and out of the machine. Watch out to not injury any of the parts on the board.
Step 5: Place the Management Board in a Secure Location
As soon as the management board is eliminated, place it in a protected location the place it will not get broken. You may put it in a plastic bag or wrap it in a towel.
Step 6: Double-Examine Your Work
Earlier than you progress on to the subsequent step, double-check your work to guarantee that the entire wires and connectors are disconnected from the management board. This may assist to stop any injury to the machine while you reassemble it.
Step 7: Troubleshooting Ideas
Should you’re having hassle disconnecting the management board, listed here are just a few troubleshooting suggestions:
| Downside | Answer |
|---|---|
| I am unable to disconnect the wires from the management board. | Just remember to’re utilizing the proper kind of pliers. Needle-nose pliers are the perfect kind of pliers for this job. |
| I am unable to take away the connectors from the management board. | Attempt utilizing a small screwdriver to softly pry the connectors up. Watch out to not injury the connectors or the board. |
| I unintentionally broken the management board. | Should you unintentionally broken the management board, you have to to switch it. You should purchase a substitute management board from the producer of your Keurig machine. |
Eradicating the Stream Sensor
The movement sensor is a small, plastic part situated within the water line of your Keurig. It helps to find out how a lot water is pumped into the brew chamber. To take away the movement sensor, observe these steps:
1. Unplug the Keurig
Earlier than you start, guarantee that the Keurig is unplugged from {the electrical} outlet.
2. Find the movement sensor
The movement sensor is situated on the underside of the Keurig, close to the water line.
3. Take away the screws
There are two screws that maintain the movement sensor in place. Take away these screws utilizing a Phillips head screwdriver.
4. Disconnect the wires
As soon as the screws are eliminated, you have to to disconnect the 2 wires which are linked to the movement sensor.
5. Take away the movement sensor
As soon as the wires are disconnected, you may take away the movement sensor by gently pulling it out of the water line.
6. Examine the movement sensor
After you have eliminated the movement sensor, take a second to examine it for any injury. If the movement sensor is broken, it’s going to should be changed.
7. Clear the movement sensor
If the movement sensor just isn’t broken, you may clear it by rinsing it with water.
8. Reinstall the movement sensor
To reinstall the movement sensor, merely reverse the steps that you just took to take away it. Make sure you tighten the screws securely, however don’t overtighten them.
Disassembling the Drip Tray
1. **Find the drip tray latch:** The drip tray is held in place by a latch situated on the underside of the machine.
2. **Press the latch:** Firmly press down on the latch to launch it.
3. **Pull out the drip tray:** As soon as the latch is launched, gently pull out the drip tray.
4. **Take away the cup help:** The cup help is a small plastic piece that sits contained in the drip tray. Grasp the cup help and pull it straight as much as take away it.
5. **Clear the drip tray and cup help:** Use a humid fabric to wipe down the drip tray and cup help. If there may be any espresso residue, use a light detergent to scrub it off.
6. **Reassemble the drip tray:** Place the cup help again into the drip tray, then insert the drip tray again into the machine.
7. **Shut the latch:** Push down on the latch to safe the drip tray in place.
Eradicating the Drip Tray Float
8. **Find the drip tray float:** The drip tray float is a small plastic ball that sits contained in the drip tray. It helps to detect when the drip tray is full.
9. **Take away the drip tray float:** To take away the drip tray float, gently push down on the float and pull it out of the drip tray. The float is held in place by a small magnet, so it could require slightly drive to take away it.
| Step | Motion |
|---|---|
| 1 | Find the drip tray latch. |
| 2 | Press the latch. |
| 3 | Pull out the drip tray. |
| 4 | Take away the cup help. |
| 5 | Clear the drip tray and cup help. |
| 6 | Reassemble the drip tray. |
| 7 | Shut the latch. |
| 8 | Find the drip tray float. |
| 9 | Take away the drip tray float. |
Cleansing and Reassembling the Parts
Now that the Keurig is disassembled, it is time to clear the parts. Use heat, soapy water and a delicate fabric to wipe down the entire detachable components. Take particular care to scrub the needle and the water reservoir.
As soon as the parts are clear, it is time to reassemble the Keurig. Begin by inserting the water reservoir into the bottom of the machine. Then, substitute the drip tray and the Ok-Cup holder.
Subsequent, insert the needle into the highest of the machine. Guarantee that the needle is correctly aligned in order that it may possibly puncture the Ok-Cups.
Lastly, substitute the highest of the machine and plug within the Keurig. Your Keurig is now prepared to make use of!
Cleansing the Water Reservoir
The water reservoir is likely one of the most vital parts of your Keurig. It is vital to scrub the water reservoir repeatedly to stop the buildup of mould and micro organism.
To wash the water reservoir, take away it from the Keurig and rinse it with heat water. Then, add just a few drops of dish cleaning soap to the water reservoir and swish it round. Lastly, rinse the water reservoir completely with heat water and substitute it within the Keurig.
Cleansing the Needle
The needle is one other vital part of your Keurig. It is vital to scrub the needle repeatedly to stop it from clogging. Some keurig fashions have a detachable needle, whereas others don’t. To wash the needle, merely use a delicate fabric and gently wipe away any espresso grounds or different particles. In case your Keurig mannequin has a detachable needle, you may take away it and soak it in heat, soapy water for a couple of minutes. Then, rinse the needle completely with heat water and substitute it within the Keurig.
Cleansing the Ok-Cup Holder
The Ok-Cup holder is one other part of your Keurig that needs to be cleaned repeatedly. To wash the Ok-Cup holder, merely take away it from the Keurig and rinse it with heat water. Then, use a delicate fabric to wipe away any espresso grounds or different particles. Lastly, substitute the Ok-Cup holder within the Keurig.
| Kind | Cleansing methodology |
|---|---|
| Water reservoir | Rinse with heat water, add just a few drops of dish cleaning soap, swish round, rinse completely |
| Needle | Wipe with a delicate fabric, take away and soak in heat, soapy water (if detachable) |
| Ok-Cup holder | Rinse with heat water, wipe with a delicate fabric |
How To Take Aside A Keurig
Listed below are the steps on how you can take aside a Keurig:
- Unplug the Keurig and let it calm down.
- Take away the water reservoir and drip tray.
- Flip the Keurig the other way up and take away the 4 screws that maintain the underside panel in place.
- Fastidiously elevate the underside panel off of the Keurig.
- Find the 2 screws that maintain the heating ingredient in place and take away them.
- Fastidiously elevate the heating ingredient out of the Keurig.
- Find the 2 screws that maintain the pump in place and take away them.
- Fastidiously elevate the pump out of the Keurig.
- Find the 2 screws that maintain the management board in place and take away them.
- Fastidiously elevate the management board out of the Keurig.
Individuals Additionally Ask About How To Take Aside A Keurig
How do I clear the within of my Keurig?
To wash the within of your Keurig, you have to to descale it. Descaling is the method of eradicating mineral buildup from the within of the Keurig. You may descale your Keurig utilizing a descaling answer or vinegar.
How do I repair a Keurig that’s not brewing?
In case your Keurig just isn’t brewing, there are some things you may test:
- Guarantee that the Keurig is plugged in and turned on.
- Guarantee that there may be water within the water reservoir.
- Guarantee that the Ok-cup is correctly inserted into the Keurig.
- Guarantee that the needle within the Keurig just isn’t clogged.
How do I substitute the water filter in my Keurig?
To exchange the water filter in your Keurig, you have to to:
- Take away the water reservoir from the Keurig.
- Find the water filter within the backside of the water reservoir.
- Take away the previous water filter and insert the brand new water filter.
- Substitute the water reservoir within the Keurig.
